Menu
Your Cart

MG120X300-OV7X25-F20-C

MG120X300-OV7X25-F20-C
MG120X300-OV7X25-F20-C

MG120X300-OV7X25-F20-C Replacement Foam Pad — 120 x 300 mm

This 120 x 300 mm replacement foam pad is the wear surface for a compatible Vacuforce MG large-area vacuum gripper. It is a spare sealing pad, not a complete gripper, valve assembly or vacuum generator.

This 20 mm thick, self-adhesive closed-cell neoprene foam provides a compliant contact seal against the workpiece. It is supplied as a replacement pad for the corresponding MG vacuum gripper model.

MG120X300-OV7X25-F20-CReplacement pad model
120 x 300 mmPad footprint
Closed-cell neopreneFoam material
Self-adhesiveAttachment

Technical Specifications

SpecificationDetails
ModelMG120X300-OV7X25-F20-C
Product FamilyReplacement Foam Pad
ManufacturerVacuforce
Pad Footprint120 x 300 mm
Pad MaterialClosed-cell neoprene foam
Foam Thickness20 mm
AttachmentSelf-adhesive backing
Supplied ItemReplacement foam contact pad only
HTS Code7616.99.5190

What the replacement foam pad does

The foam pad provides a compliant sealing contact face between the MG gripper and the load. It can be replaced when the contact surface is torn, permanently compressed or no longer seals reliably. The valves and the vacuum source are separate components of the gripper system; replacing the foam alone does not service either of them.

Replacement Pad Construction and Fit

  • Correct fit: designed for the 120 x 300 mm MG contact footprint; order by the exact replacement pad model number.
  • Material: closed-cell neoprene foam, as identified in the existing product listing.
  • Installation: self-adhesive backing; clean the gripper contact face, position the replacement pad correctly and press it firmly into place.
  • Vacuum passages: the openings allow vacuum to reach the load through the foam face; keep them unobstructed during installation.
  • Scope of supply: replacement foam pad only. The complete gripper body, valves and vacuum source are separate.

Maintenance Applications

  • Replacement of worn or damaged MG gripper sealing foam
  • Routine maintenance of automated carton and case-handling grippers
  • Restoration of contact sealing on a compatible large-area vacuum end effector

Important: Order by the exact replacement model and overall pad footprint. Remove old adhesive residue and keep vacuum passages clear. This spare pad is not a complete vacuum gripper.

Frequently Asked Questions

Is this a complete vacuum gripper or just a replacement pad?

This listing is for the MG120X300-OV7X25-F20-C replacement foam pad only. The aluminum gripper body, self-closing valves, mounting hardware and vacuum generator are not included in this pad description.

What do the openings in the foam pad do?

The openings let vacuum reach the workpiece through the foam sealing surface. They must remain clear so the gripper can develop vacuum at the contact face.

What material is used for the replacement contact surface?

The existing product specification identifies closed-cell neoprene foam with self-adhesive backing. Confirm chemical and temperature suitability for the work environment before use.

How do I know this is the correct MG gripper foam pad?

Use the exact replacement part number MG120X300-OV7X25-F20-C. This pad measures 120 x 300 mm overall and is 20 mm thick. Match the model number to the intended MG gripper rather than relying on overall dimensions alone.

When should an MG gripper foam pad be replaced?

Replace or inspect the pad when it is torn, permanently compressed, peeling from the body or causing an unreliable seal. Also check the valve openings and vacuum supply before assuming foam wear is the only problem.

Link to Pneuforce Data Sheets
Please Login or Register to review
Please Login or Register to review
Order received by 14.00EST ship same day
Ships from Indianapolis, USA
$53.59 each
  • Stock: 12
Add to Cart
Buy Now Question about this product?
Add to Wish List Compare this Product